Search filters the loaded procedure list locally. Separate terms must all match (use quotes for an exact phrase). Cached STIG Search results apply when you arrive from Search.
Objective ID
Severity
Discussion
V-273569
medium
Information flow control regulates where information is allowed to travel within a network and between interconnected networks. The flow of all network traffic must be monitored and controlled so it does not introduce any unacceptable risk to the network infrastructure or data. Information flow control policies and enforcement mechanisms are commonly employed by organizations to control the flow of information between designated sources and destinations (e.g., networks, individuals, and devices) within information systems.
Enforcement occurs, for example, in boundary protection devices (e.g., gateways, routers, guards, encrypted tunnels, and firewalls) that employ rule sets or establish how configuration settings that restrict information system services, provide a packet filtering capability based on header information, or provide a message filtering capability based on message content (e.g., implementing key word searches or using document characteristics).
Enforcement occurs, for example, in boundary protection devices (e.g., gateways, routers, guards, encrypted tunnels, and firewalls) that employ rule sets or establish how configuration settings that restrict information system services, provide a packet filtering capability based on header information, or provide a message filtering capability based on message content (e.g., implementing key word searches or using document characteristics).
V-273570
medium
Accepting route advertisements for Bogon prefixes can result in the local autonomous system (AS) becoming a transit for malicious traffic as it will in turn advertise these prefixes to neighbor autonomous systems.
V-273571
medium
Accepting route advertisements belonging to the local AS can result in traffic looping or being black holed, or at a minimum using a nonoptimized path.
V-273572
medium
As a best practice, a service provider should only accept customer prefixes that have been assigned to that customer and any peering autonomous systems. A multi-homed customer with BGP speaking routers connected to the internet or other external networks could be breached and used to launch a prefix de-aggregation attack. Without ingress route filtering of customers, the effectiveness of such an attack could impact the entire IP core and its customers.
V-273573
medium
Advertisement of routes by an autonomous system for networks that do not belong to any of its customers pulls traffic away from the authorized network. This causes a denial of service (DoS) on the network that allocated the block of addresses and may cause a DoS on the network that is inadvertently advertising it as the originator. It is also possible that a misconfigured or compromised router within the GIG IP core could redistribute IGP routes into BGP, thereby leaking internal routes.
V-273574
low
Verifying the path a route has traversed will ensure the IP core is not used as a transit network for unauthorized or possibly even internet traffic. All autonomous system boundary routers (ASBRs) must ensure updates received from eBGP peers list their AS number as the first AS in the AS_PATH attribute.
V-273575
low
The interoperability of BGP extensions for interdomain multicast routing and MSDP enables seamless connectivity of multicast domains between autonomous systems. MP-BGP advertises the unicast prefixes of the multicast sources used by Protocol Independent Multicast (PIM) routers to perform RPF checks and build multicast distribution trees. MSDP is a mechanism used to connect multiple PIM sparse-mode domains, allowing RPs from different domains to share information about active sources. When RPs in peering multicast domains hear about active sources, they can pass on that information to their local receivers, thereby allowing multicast data to be forwarded between the domains. Configuring an import policy to block multicast advertisements for reserved, Martian, single-source multicast, and any other undesirable multicast groups, as well as any source-group (S, G) states with Bogon source addresses, would assist in avoiding unwanted multicast traffic from traversing the core.
V-273576
low
To avoid global visibility of local information, there are a number of source-group (S, G) states in a PIM-SM domain that must not be leaked to another domain, such as multicast sources with private address, administratively scoped multicast addresses, and the auto-RP groups (224.0.1.39 and 224.0.1.40).
Allowing a multicast distribution tree, local to the core, to extend beyond its boundary could enable local multicast traffic to leak into other autonomous systems and customer networks.
Allowing a multicast distribution tree, local to the core, to extend beyond its boundary could enable local multicast traffic to leak into other autonomous systems and customer networks.
V-273577
low
To reduce any risk of a denial-of-service (DoS) attack from a rogue or misconfigured MSDP router, the router must be configured to limit the number of source-active messages it accepts from each peer.
V-273578
low
Verifying the path a route has traversed will ensure the local AS is not used as a transit network for unauthorized traffic. To ensure that the local AS does not carry any prefixes that do not belong to any customers, all PE routers must be configured to reject routes with an originating AS other than that belonging to the customer.
V-273580
medium
Information flow control regulates authorized information to travel within a network and between interconnected networks. Controlling the flow of network traffic is critical so it does not introduce any unacceptable risk to the network infrastructure or data. An example of a flow control restriction is blocking outside traffic claiming to be from within the organization. For most routers, internal information flow control is a product of system design.
V-273581
medium
If multicast traffic is forwarded beyond the intended boundary, it is possible that it can be intercepted by unauthorized or unintended personnel. Limiting where, within the network, a given multicast group's data is permitted to flow is an important first step in improving multicast security.
A scope zone is an instance of a connected region of a given scope. Zones of the same scope cannot overlap while zones of a smaller scope will fit completely within a zone of a larger scope. For example, Admin-local scope is smaller than Site-local scope, so the administratively configured boundary fits within the bounds of a site. According to RFC 4007 IPv6 Scoped Address Architecture (section 5), scope zones are also required to be "convex from a routing perspective"; that is, packets routed within a zone must not pass through any links that are outside of the zone. This requirement forces each zone to be one contiguous island rather than a series of separate islands.
As stated in the DOD IPv6 IA Guidance for MO3, "One should be able to identify all interfaces of a zone by drawing a closed loop on their network diagram, engulfing some routers and passing through some routers to include only some of their interfaces." Therefore, it is imperative that the network engineers have documented their multicast topology and know which interfaces are enabled for multicast. Once this is done, the zones can be scoped as required.
A scope zone is an instance of a connected region of a given scope. Zones of the same scope cannot overlap while zones of a smaller scope will fit completely within a zone of a larger scope. For example, Admin-local scope is smaller than Site-local scope, so the administratively configured boundary fits within the bounds of a site. According to RFC 4007 IPv6 Scoped Address Architecture (section 5), scope zones are also required to be "convex from a routing perspective"; that is, packets routed within a zone must not pass through any links that are outside of the zone. This requirement forces each zone to be one contiguous island rather than a series of separate islands.
As stated in the DOD IPv6 IA Guidance for MO3, "One should be able to identify all interfaces of a zone by drawing a closed loop on their network diagram, engulfing some routers and passing through some routers to include only some of their interfaces." Therefore, it is imperative that the network engineers have documented their multicast topology and know which interfaces are enabled for multicast. Once this is done, the zones can be scoped as required.
V-273582
medium
PIM is a routing protocol used to build multicast distribution trees for forwarding multicast traffic across the network infrastructure. PIM traffic must be limited to only known PIM neighbors by configuring and binding a PIM neighbor filter to those interfaces that have PIM enabled. If a PIM neighbor filter is not applied to those interfaces that have PIM enabled, unauthorized routers can join the PIM domain, discover and use the rendezvous points, and also advertise their rendezvous points into the domain. This can result in a denial of service by traffic flooding or result in the unauthorized transfer of data.
V-273583
low
If multicast traffic is forwarded beyond the intended boundary, it is possible that it can be intercepted by unauthorized or unintended personnel.
Administrative scoped multicast addresses are locally assigned and are to be used exclusively by the enterprise network or enclave. Administrative scoped multicast traffic must not cross the enclave perimeter in either direction. Restricting multicast traffic makes it more difficult for a malicious user to access sensitive traffic.
Admin-Local scope is encouraged for any multicast traffic within a network intended for network management, as well as for control plane traffic that must reach beyond link-local destinations.
Administrative scoped multicast addresses are locally assigned and are to be used exclusively by the enterprise network or enclave. Administrative scoped multicast traffic must not cross the enclave perimeter in either direction. Restricting multicast traffic makes it more difficult for a malicious user to access sensitive traffic.
Admin-Local scope is encouraged for any multicast traffic within a network intended for network management, as well as for control plane traffic that must reach beyond link-local destinations.
V-273584
low
An inactive interface is rarely monitored or controlled and may expose a network to an undetected attack on that interface. Unauthorized personnel with access to the communication facility could gain access to a router by connecting to a configured interface that is not in use.
If an interface is no longer used, the configuration must be deleted and the interface disabled. For sub-interfaces, delete sub-interfaces that are on inactive interfaces and delete sub-interfaces that are themselves inactive. If the sub-interface is no longer necessary for authorized communications, it must be deleted.
If an interface is no longer used, the configuration must be deleted and the interface disabled. For sub-interfaces, delete sub-interfaces that are on inactive interfaces and delete sub-interfaces that are themselves inactive. If the sub-interface is no longer necessary for authorized communications, it must be deleted.
V-273585
high
Enclaves with alternate gateway connections must take additional steps to ensure there is no compromise on the enclave network or NIPRNet. Without verifying the destination address of traffic coming from the site's alternate gateway, the perimeter router could be routing transit data from the internet into the NIPRNet. This could also make the perimeter router vulnerable to a denial-of-service (DoS) attack as well as provide a back door into the NIPRNet. The DOD enclave must ensure the ingress filter applied to external interfaces on a perimeter router connecting to an Approved Gateway is secure through filters permitting packets with a destination address belonging to the DOD enclave's address block.
V-273586
high
ISPs use BGP to share route information with other autonomous systems (i.e., other ISPs and corporate networks). If the perimeter router was configured to BGP peer with an ISP, NIPRNet routes could be advertised to the ISP, thereby creating a backdoor connection from the internet to the NIPRNet.
V-273587
low
If the static routes to the alternate gateway are being redistributed into an Exterior Gateway Protocol or Interior Gateway Protocol to a NIPRNet gateway, this could make traffic on NIPRNet flow to that particular router and not to the Internet Access Pointerface routers. This could not only wreak havoc with traffic flows on NIPRNet, but it could overwhelm the connection from the router to the NIPRNet gateway(s) and also cause traffic destined for outside of NIPRNet to bypass the defenses of the Internet Access Points.
V-273588
medium
If the gateway router is not a dedicated device for the OOBM network, implementation of several safeguards for containment of management and production traffic boundaries must occur. Since the managed and management network are separate routing domains, configuration of separate IGP routing instances is critical on the router to segregate traffic from each network.
V-273589
medium
If the gateway router is not a dedicated device for the OOBM network, several safeguards must be implemented for containment of management and production traffic boundaries; otherwise, it is possible that management traffic will not be separated from production traffic.
Since the managed network and the management network are separate routing domains, separate Interior Gateway Protocol (IGP) routing instances must be configured on the router, one for the managed network and one for the OOBM network. In addition, the routes from the two domains must not be redistributed to each other.
Since the managed network and the management network are separate routing domains, separate Interior Gateway Protocol (IGP) routing instances must be configured on the router, one for the managed network and one for the OOBM network. In addition, the routes from the two domains must not be redistributed to each other.
V-273590
low
Real-time multicast traffic can entail multiple large flows of data. An attacker can flood a network segment with multicast packets, over-using the available bandwidth and thereby creating a denial-of-service (DoS) condition. Hence, it is imperative that register messages are accepted only for authorized multicast groups and sources.
V-273591
low
Real-time multicast traffic can entail multiple large flows of data. An attacker can flood a network segment with multicast packets, over-using the available bandwidth and thereby creating a denial-of-service (DoS) condition. Hence, it is imperative that join messages are only accepted for authorized multicast groups.
V-273594
low
Auditing and logging are key components of any security architecture. It is essential for security personnel to know what is being done or attempted to be done, and by whom, to compile an accurate risk assessment. Auditing the actions on network devices provides a means to recreate an attack or identify a configuration mistake on the device.
V-273596
medium
Call home services will routinely send data such as configuration and diagnostic information to the vendor for routine or emergency analysis and troubleshooting. There is a risk that transmission of sensitive data sent to unauthorized persons could result in data loss or downtime due to an attack.
V-273597
medium
A rogue router could send a fictitious routing update to convince a site's perimeter router to send traffic to an incorrect or even a rogue destination. This diverted traffic could be analyzed to learn confidential information about the site's network or used to disrupt the network's ability to communicate with other networks. This is known as a "traffic attraction attack" and is prevented by configuring neighbor router authentication for routing updates. However, using clear-text authentication provides little benefit since an attacker can intercept traffic and view the authentication key. This would allow the attacker to use the authentication key in an attack.
Since MD5 is vulnerable to "birthday" attacks and may be compromised, routing protocol authentication must use FIPS 198-1 validated algorithms and modules to encrypt the authentication key. This requirement applies to all IPv4 and IPv6 protocols that are used to exchange routing or packet forwarding information; this includes all Interior Gateway Protocols (such as OSPF, EIGRP, and IS-IS) and Exterior Gateway Protocols (such as BGP), MPLS-related protocols (such as LDP), and multicast-related protocols.
Satisfies: SRG-NET-000168-RTR-000078, SRG-NET-000168-RTR-000077
Since MD5 is vulnerable to "birthday" attacks and may be compromised, routing protocol authentication must use FIPS 198-1 validated algorithms and modules to encrypt the authentication key. This requirement applies to all IPv4 and IPv6 protocols that are used to exchange routing or packet forwarding information; this includes all Interior Gateway Protocols (such as OSPF, EIGRP, and IS-IS) and Exterior Gateway Protocols (such as BGP), MPLS-related protocols (such as LDP), and multicast-related protocols.
Satisfies: SRG-NET-000168-RTR-000078, SRG-NET-000168-RTR-000077
V-273601
medium
DoS is a condition when a resource is not available for legitimate users. Packet flooding distributed denial-of-service (DDoS) attacks are referred to as volumetric attacks and have the objective of overloading a network or circuit to deny or seriously degrade performance, which denies access to the services that normally traverse the network or circuit. Volumetric attacks have become relatively easy to launch using readily available tools such as Low Orbit Ion Cannon or botnets.
Measures to mitigate the effects of a successful volumetric attack must be taken to ensure that sufficient capacity is available for mission-critical traffic. Managing capacity may include, for example, establishing selected network usage priorities or quotas and enforcing them using rate limiting, Quality of Service (QoS), or other resource reservation control methods. These measures may also mitigate the effects of sudden decreases in network capacity that are the result of accidental or intentional physical damage to telecommunications facilities (such as cable cuts or weather-related outages).
Measures to mitigate the effects of a successful volumetric attack must be taken to ensure that sufficient capacity is available for mission-critical traffic. Managing capacity may include, for example, establishing selected network usage priorities or quotas and enforcing them using rate limiting, Quality of Service (QoS), or other resource reservation control methods. These measures may also mitigate the effects of sudden decreases in network capacity that are the result of accidental or intentional physical damage to telecommunications facilities (such as cable cuts or weather-related outages).
V-273602
low
Different applications have unique requirements and toleration levels for delay, jitter, bandwidth, packet loss, and availability. To manage the multitude of applications and services, a network requires a QoS framework to differentiate traffic and provide a method to manage network congestion. The Differentiated Services Model (DiffServ) is based on per-hop behavior by categorizing traffic into different classes and enabling each node to enforce a forwarding treatment to each packet as dictated by a policy.
Packet markings such as IP Precedence and its successor, Differentiated Services Code Points (DSCP), were defined along with specific per-hop behaviors for key traffic types to enable a scalable QoS solution. DiffServ QoS categorizes network traffic, prioritizes it according to its relative importance, and provides priority treatment based on the classification. It is imperative that end-to-end QoS is implemented within the IP core network to provide preferred treatment for mission-critical applications.
Packet markings such as IP Precedence and its successor, Differentiated Services Code Points (DSCP), were defined along with specific per-hop behaviors for key traffic types to enable a scalable QoS solution. DiffServ QoS categorizes network traffic, prioritizes it according to its relative importance, and provides priority treatment based on the classification. It is imperative that end-to-end QoS is implemented within the IP core network to provide preferred treatment for mission-critical applications.
V-273603
low
Different applications have unique requirements and toleration levels for delay, jitter, bandwidth, packet loss, and availability. To manage the multitude of applications and services, a network requires a QoS framework to differentiate traffic and provide a method to manage network congestion. The Differentiated Services Model (DiffServ) is based on per-hop behavior by categorizing traffic into different classes and enabling each node to enforce a forwarding treatment to each packet as dictated by a policy.
Packet markings such as IP Precedence and its successor, Differentiated Services Code Points (DSCP), were defined along with specific per-hop behaviors for key traffic types to enable a scalable QoS solution. DiffServ QoS categorizes network traffic, prioritizes it according to its relative importance, and provides priority treatment based on the classification. It is imperative that end-to-end QoS is implemented within the IP core network to provide preferred treatment for mission-critical applications.
Packet markings such as IP Precedence and its successor, Differentiated Services Code Points (DSCP), were defined along with specific per-hop behaviors for key traffic types to enable a scalable QoS solution. DiffServ QoS categorizes network traffic, prioritizes it according to its relative importance, and provides priority treatment based on the classification. It is imperative that end-to-end QoS is implemented within the IP core network to provide preferred treatment for mission-critical applications.
V-273604
high
A deny-all, permit-by-exception network communications traffic policy ensures that only connections that are essential and approved are allowed.
This requirement applies to both inbound and outbound network communications traffic. All inbound and outbound traffic must be denied by default. Firewalls and perimeter routers should only allow traffic through that is explicitly permitted. The initial defense for the internal network is to block any traffic at the perimeter that is attempting to make a connection to a host residing on the internal network. In addition, allowing unknown or undesirable outbound traffic by the firewall or router will establish a state that will permit the return of this undesirable traffic inbound.
This requirement applies to both inbound and outbound network communications traffic. All inbound and outbound traffic must be denied by default. Firewalls and perimeter routers should only allow traffic through that is explicitly permitted. The initial defense for the internal network is to block any traffic at the perimeter that is attempting to make a connection to a host residing on the internal network. In addition, allowing unknown or undesirable outbound traffic by the firewall or router will establish a state that will permit the return of this undesirable traffic inbound.
V-273605
high
The route processor handles traffic destined to the router, the key component used to build forwarding paths, and is instrumental with all network management functions. Hence, any disruption or denial-of-service (DoS) attack to the route processor can result in mission critical network outages.
V-273606
medium
Fragmented ICMP packets can be generated by hackers for denial-of-service (DoS) attacks such as Ping O' Death and Teardrop. It is imperative that all fragmented ICMP packets are dropped.
V-273607
medium
Vulnerability assessments must be reviewed by the system administrator, and protocols must be approved by the information assurance (IA) staff before entering the enclave.
Access control lists (ACLs) are the first line of defense in a layered security approach. They permit authorized packets and deny unauthorized packets based on port or service type. They enhance the posture of the network by not allowing packets to reach a potential target within the security domain. The lists provided are highly susceptible ports and services that should be blocked or limited as much as possible without adversely affecting customer requirements. Auditing packets attempting to penetrate the network but that are stopped by an ACL will allow network administrators to broaden their protective ring and more tightly define the scope of operation.
If the perimeter is in a Deny-by-Default posture and what is allowed through the filter is in accordance with DOD Instruction 8551.1, and if the permit rule is explicitly defined with explicit ports and protocols allowed, then all requirements related to PPS being blocked would be satisfied.
Access control lists (ACLs) are the first line of defense in a layered security approach. They permit authorized packets and deny unauthorized packets based on port or service type. They enhance the posture of the network by not allowing packets to reach a potential target within the security domain. The lists provided are highly susceptible ports and services that should be blocked or limited as much as possible without adversely affecting customer requirements. Auditing packets attempting to penetrate the network but that are stopped by an ACL will allow network administrators to broaden their protective ring and more tightly define the scope of operation.
If the perimeter is in a Deny-by-Default posture and what is allowed through the filter is in accordance with DOD Instruction 8551.1, and if the permit rule is explicitly defined with explicit ports and protocols allowed, then all requirements related to PPS being blocked would be satisfied.
V-273608
medium
Access lists are used to separate data traffic into that which it will route (permitted packets) and that which it will not route (denied packets). Secure configuration of routers makes use of access lists for restricting access to services on the router itself as well as for filtering traffic passing through the router.
Inbound versus Outbound: Note that some operating systems default access lists are applied to the outbound queue. The more secure solution is to apply the access list to the inbound queue for three reasons:
- The router can protect itself before damage is inflicted.
- The input port is still known and can be filtered on.
- It is more efficient to filter packets before routing them.
Inbound versus Outbound: Note that some operating systems default access lists are applied to the outbound queue. The more secure solution is to apply the access list to the inbound queue for three reasons:
- The router can protect itself before damage is inflicted.
- The input port is still known and can be filtered on.
- It is more efficient to filter packets before routing them.
V-273609
medium
Access lists are used to separate data traffic into that which it will route (permitted packets) and that which it will not route (denied packets). Secure configuration of routers makes use of access lists for restricting access to services on the router itself as well as for filtering traffic passing through the router.
Inbound versus Outbound: Note that some operating systems default access lists are applied to the outbound queue. The more secure solution is to apply the access list to the inbound queue for three reasons:
- The router can protect itself before damage is inflicted.
- The input port is still known and can be filtered on.
- It is more efficient to filter packets before routing them.
Inbound versus Outbound: Note that some operating systems default access lists are applied to the outbound queue. The more secure solution is to apply the access list to the inbound queue for three reasons:
- The router can protect itself before damage is inflicted.
- The input port is still known and can be filtered on.
- It is more efficient to filter packets before routing them.
V-273610
medium
Outbound route advertisements belonging to the core can result in traffic either looping or being black holed, or at a minimum, using a nonoptimized path.
V-273611
high
IP/MPLS networks providing VPN and transit services must provide, at the least, the same level of protection against denial-of-service (DoS) attacks and intrusions as layer 2 networks. Although the IP core network elements are hidden, security should never rely entirely on obscurity.
IP addresses can be guessed. Core network elements must not be accessible from any external host. Protecting the core from any attack is vital for the integrity and privacy of customer traffic as well as the availability of transit services. A compromise of the IP core can result in an outage or, at a minimum, nonoptimized forwarding of customer traffic. Protecting the core from an outside attack also prevents attackers from using the core to attack any customer. Hence, it is imperative that all routers at the edge deny traffic destined to any address belonging to the IP core infrastructure.
IP addresses can be guessed. Core network elements must not be accessible from any external host. Protecting the core from any attack is vital for the integrity and privacy of customer traffic as well as the availability of transit services. A compromise of the IP core can result in an outage or, at a minimum, nonoptimized forwarding of customer traffic. Protecting the core from an outside attack also prevents attackers from using the core to attack any customer. Hence, it is imperative that all routers at the edge deny traffic destined to any address belonging to the IP core infrastructure.
V-273612
medium
The uRPF feature is a defense against spoofing and denial-of-service (DoS) attacks by verifying if the source address of any ingress packet is reachable. To mitigate attacks that rely on forged source addresses, all provider edge routers must enable uRPF loose mode to guarantee that all packets received from a CE router contain source addresses that are in the route table.
V-273613
medium
When the production network is managed in-band or out-of-band (OOBM), the management network could be housed at a NOC that is located remotely at single or multiple interconnected sites. NOC interconnectivity, as well as connectivity between the NOC and the managed network, must be enabled using IPsec tunnels or dedicated circuits to provide the separation and integrity of the managed traffic.
V-273614
medium
The OOBM network is an IP network used exclusively for the transport of operations, administration, maintenance, and provisioning (OAM&P) data from the network being managed to the operations support system (OSS) components located at the NOC. Its design provides connectivity to each managed network device, enabling network management traffic to flow between the managed network elements and the NOC. This allows the use of paths separate from those used by the managed network.
V-273615
medium
If the gateway router is not a dedicated device for the OOBM network, several safeguards must be implemented for containment of management and production traffic boundaries. It is imperative that hosts from the managed network are not able to access the OOBM gateway router.
V-273616
medium
The OOBM access switch will connect to the management interface of the managed network elements. The management interface can be a true OOBM interface or a standard interface functioning as the management interface. In either case, the management interface of the managed network element will be directly connected to the OOBM network.
An OOBM interface does not forward transit traffic, thereby providing complete separation of production and management traffic. Since all management traffic is immediately forwarded into the management network, it is not exposed to possible tampering. The separation also ensures that congestion or failures in the managed network do not affect the management of the device. If the device does not have an OOBM port, the interface functioning as the management interface must be configured so that management traffic does not leak into the managed network and that production traffic does not leak into the management network.
An OOBM interface does not forward transit traffic, thereby providing complete separation of production and management traffic. Since all management traffic is immediately forwarded into the management network, it is not exposed to possible tampering. The separation also ensures that congestion or failures in the managed network do not affect the management of the device. If the device does not have an OOBM port, the interface functioning as the management interface must be configured so that management traffic does not leak into the managed network and that production traffic does not leak into the management network.
V-273618
high
A compromised host in an enclave can be used by a malicious platform to launch cyberattacks on third parties. This is a common practice in "botnets", which are a collection of compromised computers using malware to attack other computers or networks. Distributed denial-of-service (DDoS) attacks frequently leverage IP source address spoofing to send packets to multiple hosts that in turn will then send return traffic to the hosts with the IP addresses that were forged. This can generate significant amounts of traffic. Therefore, protection measures to counteract IP source address spoofing must be taken. When uRPF is enabled in strict mode, the packet must be received on the interface that the device would use to forward the return packet; thereby mitigating IP source address spoofing.
V-273619
medium
Packets with IP options are not fast switched and henceforth must be punted to the router processor. Hackers who initiate denial-of-service (DoS) attacks on routers commonly send large streams of packets with IP options. Dropping the packets with IP options reduces the load of IP options packets on the router. The end result is a reduction in the effects of the DoS attack on the router and on downstream routers.
V-273620
medium
Packets with IP options are not fast switched and therefore must be punted to the router processor. Hackers who initiate denial-of-service (DoS) attacks on routers commonly send large streams of packets with IP options. Dropping the packets with IP options reduces the load of IP options packets on the router. The end result is a reduction in the effects of the DoS attack on the router and on downstream routers.
V-273621
medium
A rogue router could send a fictitious routing update to convince a site's perimeter router to send traffic to an incorrect or even a rogue destination. This diverted traffic could be analyzed to learn confidential information about the site's network or used to disrupt the network's ability to communicate with other networks. This is known as a "traffic attraction attack" and is prevented by configuring neighbor router authentication for routing updates.
This requirement applies to all IPv4 and IPv6 protocols used to exchange routing or packet forwarding information. This includes BGP, RIP, OSPF, EIGRP, IS-IS, and LDP.
This requirement applies to all IPv4 and IPv6 protocols used to exchange routing or packet forwarding information. This includes BGP, RIP, OSPF, EIGRP, IS-IS, and LDP.
V-273622
medium
If the same keys are used between eBGP neighbors, the chance of a hacker compromising any of the BGP sessions increases. It is possible that a malicious user exists in one autonomous system who would know the key used for the eBGP session. This user would then be able to hijack BGP sessions with other trusted neighbors.
V-273623
medium
If the keys used for routing protocol authentication are guessed, the malicious user could create havoc within the network by advertising incorrect routes and redirecting traffic. Some routing protocols allow the use of key chains for authentication. A key chain is a set of keys used in succession, with each having a lifetime of no more than 180 days. Changing the keys frequently reduces the risk of them eventually being guessed.
Keys cannot be used during time periods for which they are not activated. If a time period occurs during which no key is activated, neighbor authentication cannot occur, and therefore routing updates will fail. Therefore, ensure that for a given key chain, key activation times overlap to avoid any period of time during which no key is activated.
Keys cannot be used during time periods for which they are not activated. If a time period occurs during which no key is activated, neighbor authentication cannot occur, and therefore routing updates will fail. Therefore, ensure that for a given key chain, key activation times overlap to avoid any period of time during which no key is activated.
V-273626
medium
MSDP peering with customer network routers presents additional risks to the core, whether from a rogue or misconfigured MSDP-enabled router. MSDP password authentication is used to validate each segment sent on the TCP connection between MSDP peers, protecting the MSDP session against the threat of spoofed packets being injected into the TCP connection stream.
V-273627
medium
Network devices configured via a zero-touch deployment or auto-loading feature can have their startup configuration or image pushed to the device for installation via TFTP or Remote Copy (rcp). Loading an image or configuration file from the network is taking a security risk because the file could be intercepted by an attacker who could corrupt the file, resulting in a denial of service.
V-273628
medium
The Route Processor (RP) is critical to all network operations because it is the component used to build all forwarding paths for the data plane via control plane processes. It is also instrumental with ongoing network management functions that keep the routers and links available for providing network services. Any disruption to the RP or the control and management planes can result in mission-critical network outages.
A DoS attack targeting the RP can result in excessive CPU and memory utilization. To maintain network stability and RP security, the router must be able to handle specific control plane and management plane traffic destined to the RP. In the past, one method of filtering was to use ingress filters on forwarding interfaces to filter both forwarding path and receiving path traffic. However, this method does not scale well as the number of interfaces grows and the size of the ingress filters grows. Control plane policing increases the security of routers and multilayer switches by protecting the RP from unnecessary or malicious traffic. Filtering and rate limiting the traffic flow of control plane packets can be implemented to protect routers against reconnaissance and DoS attacks, allowing the control plane to maintain packet forwarding and protocol states despite an attack or heavy load on the router or multilayer switch.
A DoS attack targeting the RP can result in excessive CPU and memory utilization. To maintain network stability and RP security, the router must be able to handle specific control plane and management plane traffic destined to the RP. In the past, one method of filtering was to use ingress filters on forwarding interfaces to filter both forwarding path and receiving path traffic. However, this method does not scale well as the number of interfaces grows and the size of the ingress filters grows. Control plane policing increases the security of routers and multilayer switches by protecting the RP from unnecessary or malicious traffic. Filtering and rate limiting the traffic flow of control plane packets can be implemented to protect routers against reconnaissance and DoS attacks, allowing the control plane to maintain packet forwarding and protocol states despite an attack or heavy load on the router or multilayer switch.
V-273629
medium
A gratuitous ARP is an ARP broadcast in which the source and destination MAC addresses are the same. It is used to inform the network about a host IP address. A spoofed gratuitous ARP message can cause network mapping information to be stored incorrectly, causing network malfunction.
V-273630
low
An IP directed broadcast is a datagram sent to the broadcast address of a subnet that is not directly attached to the sending machine. The directed broadcast is routed through the network as a unicast packet until it arrives at the target subnet, where it is converted into a link-layer broadcast. Because of the nature of the IP addressing architecture, only the last router in the chain, which is connected directly to the target subnet, can conclusively identify a directed broadcast.
IP directed broadcasts are used in the extremely common and popular smurf, or denial-of-service (DoS), attacks. In a smurf attack, the attacker sends Internet Control Message Protocol (ICMP) echo requests from a falsified source address to a directed broadcast address, causing all the hosts on the target subnet to send replies to the falsified source. By sending a continuous stream of such requests, the attacker can create a much larger stream of replies, which can completely inundate the host whose address is being falsified. This service should be disabled on all interfaces when not needed to prevent smurf and DoS attacks.
Directed broadcast can be enabled on internal facing interfaces to support services such as Wake-On-LAN. Case scenario may also include support for legacy applications where the content server and the clients do not support multicast. The content servers send streaming data using UDP broadcast. Used in conjunction with the IP multicast helper-map feature, broadcast data can be sent across a multicast topology. The broadcast streams are converted to multicast and vice versa at the first-hop routers and last-hop routers before entering and leaving the multicast transit area respectively. The last-hop router must convert the multicast to broadcast. Hence, this interface must be configured to forward a broadcast packet (i.e., a directed broadcast address is converted to the all nodes broadcast address).
IP directed broadcasts are used in the extremely common and popular smurf, or denial-of-service (DoS), attacks. In a smurf attack, the attacker sends Internet Control Message Protocol (ICMP) echo requests from a falsified source address to a directed broadcast address, causing all the hosts on the target subnet to send replies to the falsified source. By sending a continuous stream of such requests, the attacker can create a much larger stream of replies, which can completely inundate the host whose address is being falsified. This service should be disabled on all interfaces when not needed to prevent smurf and DoS attacks.
Directed broadcast can be enabled on internal facing interfaces to support services such as Wake-On-LAN. Case scenario may also include support for legacy applications where the content server and the clients do not support multicast. The content servers send streaming data using UDP broadcast. Used in conjunction with the IP multicast helper-map feature, broadcast data can be sent across a multicast topology. The broadcast streams are converted to multicast and vice versa at the first-hop routers and last-hop routers before entering and leaving the multicast transit area respectively. The last-hop router must convert the multicast to broadcast. Hence, this interface must be configured to forward a broadcast packet (i.e., a directed broadcast address is converted to the all nodes broadcast address).
V-273631
medium
The ICMP supports IP traffic by relaying information about paths, routes, and network conditions. Routers automatically send ICMP messages under a wide variety of conditions. Host unreachable ICMP messages are commonly used by attackers for network mapping and diagnosis.
V-273632
medium
The ICMP supports IP traffic by relaying information about paths, routes, and network conditions. Routers automatically send ICMP messages under a wide variety of conditions. Mask Reply ICMP messages are commonly used by attackers for network mapping and diagnosis.
V-273633
medium
The ICMP supports IP traffic by relaying information about paths, routes, and network conditions. Routers automatically send ICMP messages under a wide variety of conditions. Redirect ICMP messages are commonly used by attackers for network mapping and diagnosis.
V-273634
medium
The effects of prefix de-aggregation can degrade router performance due to the size of routing tables and also result in black-holing legitimate traffic. Initiated by an attacker or a misconfigured router, prefix de-aggregation occurs when the announcement of a large prefix is fragmented into a collection of smaller prefix announcements.
In 1997, misconfigured routers in the Florida Internet Exchange network (AS7007) de-aggregated every prefix in their routing table and started advertising the first /24 block of each of these prefixes as their own. Faced with this additional burden, the internal routers became overloaded and crashed repeatedly. This caused prefixes advertised by these routers to disappear from routing tables and reappear when the routers came back online. As the routers came back after crashing, they were flooded with the routing table information by their neighbors. The flood of information would again overwhelm the routers and cause them to crash. This process of route flapping served to destabilize not only the surrounding network but also the entire Internet. Routers trying to reach those addresses would choose the smaller, more specific /24 blocks first. This caused backbone networks throughout North America and Europe to crash.
Maximum prefix limits on peer connections combined with aggressive prefix-size filtering of customers' reachability advertisements will effectively mitigate the de-aggregation risk. BGP maximum prefix must be used on all eBGP routers to limit the number of prefixes that it should receive from a particular neighbor, whether customer or peering AS. Consider each neighbor and how many routes they should be advertising and set a threshold slightly higher than the number expected.
In 1997, misconfigured routers in the Florida Internet Exchange network (AS7007) de-aggregated every prefix in their routing table and started advertising the first /24 block of each of these prefixes as their own. Faced with this additional burden, the internal routers became overloaded and crashed repeatedly. This caused prefixes advertised by these routers to disappear from routing tables and reappear when the routers came back online. As the routers came back after crashing, they were flooded with the routing table information by their neighbors. The flood of information would again overwhelm the routers and cause them to crash. This process of route flapping served to destabilize not only the surrounding network but also the entire Internet. Routers trying to reach those addresses would choose the smaller, more specific /24 blocks first. This caused backbone networks throughout North America and Europe to crash.
Maximum prefix limits on peer connections combined with aggressive prefix-size filtering of customers' reachability advertisements will effectively mitigate the de-aggregation risk. BGP maximum prefix must be used on all eBGP routers to limit the number of prefixes that it should receive from a particular neighbor, whether customer or peering AS. Consider each neighbor and how many routes they should be advertising and set a threshold slightly higher than the number expected.
V-273635
low
The effects of prefix de-aggregation can degrade router performance due to the size of routing tables and also result in black-holing legitimate traffic. Initiated by an attacker or a misconfigured router, prefix de-aggregation occurs when the announcement of a large prefix is fragmented into a collection of smaller prefix announcements.
V-273637
low
MSDP peering between networks enables sharing of multicast source information. Enclaves with an existing multicast topology using PIM-SM can configure their RP routers to peer with MSDP routers. As a first step of defense against a denial-of-service (DoS) attack, all RP routers must limit the multicast forwarding cache to ensure that router resources are not saturated managing an overwhelming number of PIM and MSDP source-active entries.
V-273638
medium
When a new source starts transmitting in a PIM Sparse Mode network, the DR will encapsulate the multicast packets into register messages and forward them to the RP using unicast. This process can be taxing on the CPU for both the DR and the RP if the source is running at a high data rate and there are many new sources starting at the same time. This scenario can potentially occur immediately after a network failover. The rate limit for the number of register messages must be set to a relatively low value based on the known number of multicast sources within the multicast domain.
V-273639
medium
The current multicast paradigm can let any host join any multicast group at any time by sending an IGMP or MLD membership report to the DR. In a Protocol Independent Multicast (PIM) Sparse Mode network, the DR will send a PIM Join message for the group to the RP. Without any form of admission control, this can pose a security risk to the entire multicast domain - specifically the multicast routers along the shared tree from the DR to the RP that must maintain the mroute state information for each group join request. Hence, it is imperative that the DR is configured to limit the number of mroute state information that must be maintained to mitigate the risk of IGMP or MLD flooding.
V-273640
medium
ASM can have many sources for the same groups (many-to-many). For many receivers, the path via the RP may not be ideal compared with the shortest path from the source to the receiver. By default, the last-hop router will initiate a switch from the shared tree to a source-specific SPT to obtain lower latencies. This is accomplished by the last-hop router sending an (S, G) Protocol Independent Multicast (PIM) Join toward S (the source).
When the last-hop router begins to receive traffic for the group from the source via the SPT, it will send a PIM Prune message to the RP for the (S, G). The RP will then send a Prune message toward the source. The SPT switchover becomes a scaling issue for large multicast topologies that have many receivers and many sources for many groups because (S, G) entries require more memory than (*, G). Hence, it is imperative to minimize the amount of (S, G) state to be maintained by increasing the threshold that determines when the SPT switchover occurs.
When the last-hop router begins to receive traffic for the group from the source via the SPT, it will send a PIM Prune message to the RP for the (S, G). The RP will then send a Prune message toward the source. The SPT switchover becomes a scaling issue for large multicast topologies that have many receivers and many sources for many groups because (S, G) entries require more memory than (*, G). Hence, it is imperative to minimize the amount of (S, G) state to be maintained by increasing the threshold that determines when the SPT switchover occurs.
V-273641
low
GTSM is designed to protect a router's IP-based control plane from denial-of-service (DoS) attacks. Many attacks focused on CPU load and line-card overload can be prevented by implementing GTSM on all Exterior Border Gateway Protocol speaking routers.
GTSM is based on the fact that the vast majority of control plane peering is established between adjacent routers; that is, the Exterior Border Gateway Protocol peers are either between connecting interfaces or between loopback interfaces. Since TTL spoofing is considered nearly impossible, a mechanism based on an expected TTL value provides a simple and reasonably robust defense from infrastructure attacks based on forged control plane traffic.
GTSM is based on the fact that the vast majority of control plane peering is established between adjacent routers; that is, the Exterior Border Gateway Protocol peers are either between connecting interfaces or between loopback interfaces. Since TTL spoofing is considered nearly impossible, a mechanism based on an expected TTL value provides a simple and reasonably robust defense from infrastructure attacks based on forged control plane traffic.
V-273642
medium
Unrestricted traffic may contain malicious traffic that poses a threat to an enclave or to other connected networks. Additionally, unrestricted traffic may transit a network, which uses bandwidth and other resources.
Traffic can be restricted directly by an access control list (ACL), which is a firewall function, or by Policy Routing. Policy Routing is a technique used to make routing decisions based on a number of different criteria other than just the destination network, including source or destination network, source or destination address, source or destination port, protocol, packet size, and packet classification. This overrides the router's normal routing procedures used to control the specific paths of network traffic. It is normally used for traffic engineering but can also be used to meet security requirements; for example, traffic that is not allowed can be routed to the Null0 or discard interface. Policy Routing can also be used to control which prefixes appear in the routing table.
This requirement is intended to allow network administrators the flexibility to use whatever technique is most effective.
Traffic can be restricted directly by an access control list (ACL), which is a firewall function, or by Policy Routing. Policy Routing is a technique used to make routing decisions based on a number of different criteria other than just the destination network, including source or destination network, source or destination address, source or destination port, protocol, packet size, and packet classification. This overrides the router's normal routing procedures used to control the specific paths of network traffic. It is normally used for traffic engineering but can also be used to meet security requirements; for example, traffic that is not allowed can be routed to the Null0 or discard interface. Policy Routing can also be used to control which prefixes appear in the routing table.
This requirement is intended to allow network administrators the flexibility to use whatever technique is most effective.
V-273643
medium
Bogons include IP packets on the public internet that contain addresses that are not in any range allocated or delegated by the Internet Assigned Numbers Authority (IANA) or a delegated regional internet registry (RIR) and allowed for public Internet use. Bogons also include multicast, IETF reserved, and special purpose address space as defined in RFC 6890.
Security of the internet's routing system relies on the ability to authenticate an assertion of unique control of an address block. Measures to authenticate such assertions rely on the validation the address block forms as part of an existing allocated address block and must be a trustable and unique reference in the IANA address registries. The intended use of a Bogon address would only be for the purpose of address spoofing in denial-of-service attacks. Hence, it is imperative that IP packets with a source Bogon address are blocked at the network's perimeter.
Security of the internet's routing system relies on the ability to authenticate an assertion of unique control of an address block. Measures to authenticate such assertions rely on the validation the address block forms as part of an existing allocated address block and must be a trustable and unique reference in the IANA address registries. The intended use of a Bogon address would only be for the purpose of address spoofing in denial-of-service attacks. Hence, it is imperative that IP packets with a source Bogon address are blocked at the network's perimeter.
V-273644
low
LLDPs are primarily used to obtain protocol addresses of neighboring devices and discover platform capabilities of those devices. Use of SNMP with the LLDP Management Information Base (MIB) allows network management applications to learn the device type and the SNMP agent address of neighboring devices, thereby enabling the application to send SNMP queries to those devices. LLDPs are also media- and protocol-independent as they run over the data link layer; therefore, two systems that support different network-layer protocols can still learn about each other. Allowing LLDP messages to reach external network nodes is dangerous as it provides an attacker a method to obtain information of the network infrastructure that can be useful to plan an attack.
V-273645
medium
When Proxy ARP is enabled on a Cisco router, it allows that router to extend the network (at layer 2) across multiple interfaces (LAN segments). Because proxy ARP allows hosts from different LAN segments to look like they are on the same segment, proxy ARP is only safe when used between trusted LAN segments. Attackers can leverage the trusting nature of proxy ARP by spoofing a trusted host and then intercepting packets. Proxy ARP should always be disabled on router interfaces that do not require it, unless the router is being used as a LAN bridge.
V-273646
medium
For in-band management, the management network must have its own subnet to enforce control and access boundaries provided by layer 3 network nodes, such as routers and firewalls. Management traffic between the managed network elements and the management network is routed via the same links and nodes as that used for production or operational traffic. Safeguards must be implemented to ensure the management traffic does not leak past the perimeter of the managed network.
V-273647
low
Real-time multicast traffic can entail multiple large flows of data. Large unicast flows tend to be fairly isolated (i.e., someone doing a file download here or there), whereas multicast can have broader impact on bandwidth consumption, resulting in extreme network congestion. Hence, it is imperative that there is multicast admission control to restrict which multicast groups hosts are allowed to join via IGMP or MLD.
V-273648
medium
Real-time multicast traffic can entail multiple large flows of data. Large unicast flows tend to be fairly isolated (i.e., someone doing a file download here or there), whereas multicast can have broader impact on bandwidth consumption, resulting in extreme network congestion. Hence, it is imperative that there is multicast admission control to restrict which multicast groups hosts are allowed to join via IGMP or MLD.
V-273650
medium
One of the fragmentation weaknesses known in IPv6 is the undetermined transport packet. This packet contains an undetermined protocol due to fragmentation. Depending on the length of the IPv6 extension header chain, the initial fragment may not contain the layer four port information of the packet.
V-273651
medium
The routing header can be used maliciously to send a packet through a path where less robust security is in place, rather than through the presumably preferred path of routing protocols. Use of the routing extension header has few legitimate uses other than as implemented by Mobile IPv6.
The Type 0 Routing Header (RFC 5095) is dangerous because it allows attackers to spoof source addresses and obtain traffic in response, rather than the real owner of the address. Secondly, a packet with an allowed destination address could be sent through a Firewall using the Routing Header functionality, only to bounce to a different node once inside. The Type 1 Routing Header is defined by a specification called "Nimrod Routing," a discontinued project funded by Defense Advanced Research Projects Activity (DARPA). Assuming that most implementations will not recognize the Type 1 Routing Header, it must be dropped. The Type 3-255 Routing Header values in the routing type field are currently undefined and must be dropped inbound and outbound.
The Type 0 Routing Header (RFC 5095) is dangerous because it allows attackers to spoof source addresses and obtain traffic in response, rather than the real owner of the address. Secondly, a packet with an allowed destination address could be sent through a Firewall using the Routing Header functionality, only to bounce to a different node once inside. The Type 1 Routing Header is defined by a specification called "Nimrod Routing," a discontinued project funded by Defense Advanced Research Projects Activity (DARPA). Assuming that most implementations will not recognize the Type 1 Routing Header, it must be dropped. The Type 3-255 Routing Header values in the routing type field are currently undefined and must be dropped inbound and outbound.
V-273652
medium
These options are intended for the destination options header only. The optional and extensible natures of the IPv6 extension headers require higher scrutiny because many implementations do not always drop packets with headers that cannot be recognized. This could cause a denial of service on the target device. In addition, the type, length, value (TLV) formatting provides the ability for headers to be very large.
Satisfies: SRG-NET-000364-RTR-000202, SRG-NET-000364-RTR-000203, SRG-NET-000364-RTR-000204, SRG-NET-000364-RTR-000205, SRG-NET-000364-RTR-000206
Satisfies: SRG-NET-000364-RTR-000202, SRG-NET-000364-RTR-000203, SRG-NET-000364-RTR-000204, SRG-NET-000364-RTR-000205, SRG-NET-000364-RTR-000206
V-273654
low
Using a loopback address as the source address offers a multitude of uses for security, access, management, and scalability of the BGP routers. It is easier to construct appropriate ingress filters for router management plane traffic destined to the network management subnet since the source addresses will be from the range used for loopback interfaces instead of a larger range of addresses used for physical interfaces. Log information recorded by authentication and syslog servers will record the router's loopback address instead of the numerous physical interface addresses.
When the loopback address is used as the source for eBGP peering, the BGP session will be harder to hijack because the source address to be used is not known globally. This makes it more difficult for a hacker to spoof an eBGP neighbor. By using traceroute, a hacker can easily determine the addresses for an eBGP speaker when the IP address of an external interface is used as the source address. The routers within the iBGP domain should also use loopback addresses as the source address when establishing BGP sessions.
When the loopback address is used as the source for eBGP peering, the BGP session will be harder to hijack because the source address to be used is not known globally. This makes it more difficult for a hacker to spoof an eBGP neighbor. By using traceroute, a hacker can easily determine the addresses for an eBGP speaker when the IP address of an external interface is used as the source address. The routers within the iBGP domain should also use loopback addresses as the source address when establishing BGP sessions.
V-273660
medium
An RD provides uniqueness to the customer address spaces within the MPLS L3VPN infrastructure. The concept of the VPN-IPv4 and VPN-IPv6 address families consists of the RD prepended before the IP address. Hence, if the same IP prefix is used in several different L3VPNs, it is possible for BGP to carry several completely different routes for that prefix, one for each VPN.
Since VPN-IPv4 addresses and IPv4 addresses are different address families, BGP never treats them as comparable addresses. The purpose of the RD is to create distinct routes for common IPv4 address prefixes. On any given PE router, a single RD can define a VRF in which the entire address space may be used independently, regardless of the makeup of other VPN address spaces. Hence, it is imperative that a unique RD is assigned to each L3VPN and that the proper RD is configured for each VRF.
Since VPN-IPv4 addresses and IPv4 addresses are different address families, BGP never treats them as comparable addresses. The purpose of the RD is to create distinct routes for common IPv4 address prefixes. On any given PE router, a single RD can define a VRF in which the entire address space may be used independently, regardless of the makeup of other VPN address spaces. Hence, it is imperative that a unique RD is assigned to each L3VPN and that the proper RD is configured for each VRF.
V-273664
low
Using a loopback address as the source address offers a multitude of uses for security, access, management, and scalability of MSDP routers. It is easier to construct appropriate ingress filters for router management plane traffic destined to the network management subnet since the source addresses will be from the range used for loopback interfaces instead of a larger range of addresses used for physical interfaces. Log information recorded by authentication and syslog servers will record the router's loopback address instead of the numerous physical interface addresses.
V-273665
low
The Neighbor Discovery protocol allows a hop limit value to be advertised by routers in a Router Advertisement message being used by hosts instead of the standardized default value. If a very small value was configured and advertised to hosts on the LAN segment, communications would fail due to the hop limit reaching zero before the packets sent by a host reached its destination.
V-273666
medium
As currently defined, site local addresses are ambiguous and can be present in multiple sites. The address itself does not contain any indication of the site to which it belongs. The use of site-local addresses has the potential to adversely affect network security through leaks, ambiguity, and potential misrouting as documented in section 2 of RFC3879. RFC3879 formally deprecates the IPv6 site-local unicast prefix FEC0::/10 as defined in RFC3513.
V-273667
medium
Many of the known attacks in stateless autoconfiguration are defined in RFC 3756 were present in IPv4 ARP attacks. To mitigate these vulnerabilities, links that have no hosts connected such as the interface connecting to external gateways must be configured to suppress router advertisements.
V-273669
medium
DoS events may occur due to a variety of internal and external causes, such as an attack by an adversary or a lack of planning to support organizational needs with respect to capacity and bandwidth. Such attacks can occur across a wide range of network protocols (e.g., IPv4, IPv6). A variety of technologies are available to limit or eliminate the origination and effects of DoS events. For example, boundary protection devices can filter certain types of packets to protect system components on internal networks from being directly affected by or the source of DoS attacks. Employing increased network capacity and bandwidth combined with service redundancy also reduces the susceptibility to DoS events.
V-273670
medium
Separating critical system components and functions from other noncritical system components and functions through separate subnetworks may be necessary to reduce susceptibility to a catastrophic or debilitating breach or compromise that results in system failure. For example, physically separating the command and control function from the in-flight entertainment function through separate subnetworks in a commercial aircraft provides an increased level of assurance in the trustworthiness of critical system functions.
V-273671
medium
An incident, whether adversarial- or nonadversarial-based, can disrupt established communications paths used for system operations and organizational command and control. Alternate communications paths reduce the risk of all communications paths being affected by the same incident. To compound the problem, the inability of organizational officials to obtain timely information about disruptions or to provide timely direction to operational elements after a communications path incident, can impact the ability of the organization to respond to such incidents in a timely manner. Establishing alternate communications paths for command and control purposes, including designating alternative decision makers if primary decision makers are unavailable and establishing the extent and limitations of their actions, can greatly facilitate the organization's ability to continue to operate and take appropriate actions during an incident.